easytofix.homes+18312931196
All articles
Roofing5 min read

Roofing Underlayment Explained: The Hidden Layer That Keeps Water Out

By EasyToFix Homes Team

Underlayment is the layer of material that sits between the roof deck and the shingles, and it is one of the most important parts of a roof even though it is never seen. When shingles are damaged by wind or blown off in a storm, the underlayment is the second line of defense that keeps rain out of the home. When it fails, water reaches the wood deck, and rot, mold, and ceiling stains follow. Most homeowners never think about underlayment until a leak appears, but knowing what it is and how it works helps when a roof is repaired or replaced.

1. What underlayment is and where it sits

A roof is built in layers. At the bottom is the roof deck, usually plywood or oriented strand board, which is nailed to the rafters. Above the deck goes the underlayment, a continuous sheet that covers the whole deck. Above the underlayment go the shingles, which are the visible outer layer. The underlayment is therefore sandwiched in the middle, hidden from view once the roof is finished.

Underlayment serves two jobs. First, it sheds water that gets past the shingles, guiding it down the slope and off the roof before it can reach the wood deck. Without it, a single missing shingle would let rain straight into the attic.

2. The three main types of underlayment

Asphalt felt, often called tar paper, is the oldest type. It is made from paper or fiberglass soaked in asphalt, and it comes in 15 pound and 30 pound weights. Felt is cheap and easy to install, but it tears easily, wrinkles when wet, and breaks down faster than modern options. It is still used on budget roofs and in mild climates.

Synthetic underlayment is made from woven plastic fibers, and it has become the standard choice on most new roofs. It is lighter, stronger, and more resistant to tearing and UV damage than felt, and it stays flat and smooth during installation. Rubberized asphalt underlayment, sometimes called peel and stick, has an adhesive backing that seals tightly to the deck and around nail holes. It is the most waterproof option, and it is required by code in valleys, around chimneys, and along the eaves in cold climates where ice dams form.

3. How underlayment protects the roof deck

Shingles are designed to shed water, not to seal it out completely. Wind can drive rain up under the shingle edges, and ice can push water sideways under the courses. When that happens, the water lands on the underlayment instead of the bare wood. A good underlayment sheds that water down the slope, over the drip edge, and into the gutter, keeping the deck dry.

The seal around fasteners matters just as much. Every shingle is nailed through the underlayment into the deck, and each nail hole is a potential leak. Rubberized underlayment seals around the nail shaft, while felt and synthetic types rely on the shingle above to cover the hole. Related reading: /blog/roof-flashing-leaks-chimney-vents explains how flashing and underlayment work together around chimneys and vents.

4. Warning signs that underlayment has failed

Underlayment failure rarely shows on the outside of the roof, so the signs appear inside the home or in the attic. Water stains on the ceiling, damp insulation, and mold on the underside of the roof deck all point to water getting past the shingles and through failed underlayment. In the attic, look for darkened or soft plywood, especially in valleys and near chimneys.

Outside, the signs are more subtle. Shingles that curl, crack, or lose granules in patches may be baking on a deck that stays damp underneath. A roof that leaks only in heavy wind driven rain, but stays dry in a normal shower, often has underlayment that has torn or dried out in one area. A roofer can lift a few shingles in the suspect area to inspect the layer below without disturbing the whole roof.

5. When underlayment must be replaced

Underlayment is replaced whenever the shingles above it are removed, which means a full roof replacement always includes new underlayment. Reusing old underlayment is a false economy: it is full of nail holes, it may be brittle or torn, and it will not protect the new shingles for their full lifespan. A reputable roofer includes new underlayment in every replacement quote.

Partial replacement is possible when only one area has failed, for example a valley or a section around a chimney. The shingles in that area are removed, the damaged underlayment is cut out, new material is installed with proper overlaps, and the shingles are replaced. Related reading: /blog/how-to-find-a-roof-leak-attic-ceiling-clues shows how to trace a leak to its source before deciding on a repair.

6. What to ask a roofer about underlayment

Before a roof replacement, ask which type of underlayment the quote includes, and whether rubberized material will be used in the valleys, around chimneys, and along the eaves. Ask how the underlayment will be lapped, since each course should overlap the one below it by at least four inches so water runs down and off, never under a seam. Ask whether the price covers removing and disposing of the old underlayment.

Also ask about the brand and the warranty. Synthetic underlayment from a major manufacturer often carries a warranty of 25 years or more, while cheap felt may have no warranty at all.

When to Call a Professional

Call a professional if there are water stains on the ceiling, damp insulation in the attic, or soft or darkened plywood under the roof deck. A roofer can inspect the underlayment by lifting a few shingles, find the exact point of failure, and repair or replace the layer before the deck rots. Never walk on a roof to check underlayment yourself, since a damp deck can be weak and slippery.

For expert roofing help anywhere in the United States, call EasyToFix Homes at (844) 211-0179. A licensed roofer can inspect the roof, explain the condition of the underlayment, and replace it properly so the roof stays watertight for years.

Tap to Call a Roofer(844) 211-0179